Work truck gear, ranked for the people who load it every morning.
Shop by truck
The best ladder racks for a Ram 1500
The Ram 1500 has the widest bed rails of the four trucks on this site, which is a problem rather than a luxury when you are buying an adjustable rack. Six racks, ranked on what the makers publish.
Our top pick: the AA-Racks X31 Extendable Steel Ladder Rack, 800 lb, Two-Bar.
Heads up: we earn a commission when you buy through our links, at no extra cost to you — from Amazon Associates, and from brand partner programs we have joined directly through the Impact network. Amazon prices are pulled live and were last checked November 20, 2026; a brand list price carries the date we read it off the maker’s own page. When we cannot verify a price we say so rather than print an old one. How this site is funded.
How we know:Owner-report-verifiedSpec-verifiedWhat these mean
Tap any row for the full write-up. Prices come straight from Amazon and are never typed in by hand.
For most Ram 1500s the rack to buy is the AA-Racks X31: two bars, a published 800 lb capacity, extendable width, and a price below what a bed mat and a set of straps cost together. If the rails have to stay untouched — a leased truck, or one you intend to sell — the JY PERFORMANCE DAC875 holds on with four J-bolt clamps and publishes a 49 to 73 inch span, which is the widest adjustment range on this page and the one with the most margin left at a Ram rail. If the bed already has something on it, the MONOKING bed rack is the only rack here whose listing names the Ram 1500 by model and sets its bar height anywhere between 17 and 25 inches.
The reason this page is Ram-specific rather than generic is a number most buyers never check. The Ram 1500's exterior bed rail width is about 66 inches — the widest of the four trucks covered on this site, about an inch over an F-150 and two over a Silverado. Universal racks are dimensioned around the middle of the full-size market, so on a Ram you are not asking whether a rack is wide enough in principle. You are asking how much of its adjustment range is already used up before the rack is even on the truck.
Measure the exterior rail width yourself, outside edge to outside edge across the top of the rails nearest the cab, before you order anything. Then check that figure against the rack's published range — not against its maximum. A rack sitting at the last inch of its travel has nothing left for a bowed rail, a rail cap or a liner lip.
Why the widest bed is the harder bed to buy for
On a Toyota Tacoma the fitment problem is obvious: at about 57 inches across the rails, a great many full-size racks simply will not close up far enough. The Ram problem is the mirror image and much easier to miss, because the rack does fit — it just fits at the end of its range.
The ECOTRIC rack publishes 58 to 69 inches. At a 66 in rail that leaves three inches of travel, which is enough but not generous. On a bed with a bonded rail cap or a thick drop-in liner lip, three inches gets used quickly.
The JY PERFORMANCE rack publishes 49 to 73 inches. A Ram rail sits comfortably mid-range, which is why it is the no-drill pick here rather than on the narrower trucks where several racks tie.
AA-Racks, VEVOR and Thule publish an extendable or clamp-on fit without a numeric range. All three are sold for full-size beds and all three work on this truck; none of them tells you in advance how much adjustment is left, so the tape measure is doing the work.
How we ranked these for this truck
Five criteria, scored 0-10 and published on every card. The order is not the order on the Silverado rack page, because GM sells named bed-rail racks for its trucks and Ram's aftermarket at this price point is almost entirely universal, which shifts the weight onto adjustment range and mounting.
Published capacity. A real figure from the maker. Three of the six racks below publish one — 800 lb, 800 lb tested and 1000 lb. The other three publish nothing, and their cards say so rather than carrying an estimate of ours.
Adjustment left at 66 inches. How much travel the rack still has once it is spanning a Ram rail. This is the criterion that moves the ranking most on this page and it barely matters on the narrower trucks.
Mounting. No-drill clamps and J-bolts keep the rails intact, which matters on a truck you intend to sell or hand back and is usually the only option on a lease. Drilled mounts are stiffer and permanent, and the holes need sealing properly or they rust from the inside.
What it blocks. Rear glass, the tailgate swing, a cover, a crossover box, a RamBox lid. On a Ram the rack is usually the last thing fitted and has to live with everything already there.
Value. Against the live Amazon price, which updates when you load this page.
The picks, ranked
Prices come from Amazon when you load this page. Where no live price is available the button says check price rather than showing you a number we cannot stand behind.
800 lb published capacity, extendable width, two bars, and it costs less than a decent tonneau cover. For a trade truck that carries ladders and conduit, this is the honest value pick in the category.
Build
9.2
Capacity
9.4
Install
9.4
Versatility
9.4
Value
9.7
Why we picked it
+800 lb published, not implied
+Extendable width fits a range of beds
+Cheap enough to buy and still afford the straps
Good to know. Steel means rust at every scratch, and extendable joints mean more fasteners to check. If the rack never comes off, a welded rack would be stiffer.
A two-bar steel rack that holds the bed rails with four J-bolt clamps and nothing else: no holes to drill, no holes to seal, and it comes back off when the truck is sold. It is also one of the few racks at this price that publishes the steel gauge rather than just a rating — 10-gauge, tested to 800 lb.
Build
9.2
Capacity
9.4
Install
9.6
Versatility
9.2
Value
9.7
Why we picked it
+Publishes the steel gauge, not just a rating
+Four J-bolts and the hardware in the box — no holes in the truck
+49-73 in width range, so it moves to the next truck
Good to know. The listing rules out trucks running a tool box, a utility track or a tonneau cover — that is the maker's own exclusion, not our caution. Four J-bolts is also fewer load paths than a clamp-heavy rack, so the rail lip itself has to be sound.
Adjustable height is the feature worth having here: the bars set anywhere from 17 to 25 inches, so you clear a tool box or stay under the cab line depending on what the truck does, rather than living with whatever height the rack came at.
Build
9.1
Capacity
9.0
Install
9.1
Versatility
9.6
Value
9.4
Why we picked it
+Height adjusts across an 8 in range — clear a tool box or stay under the cab line
+Named fitment across every full-size truck we cover
+Two crossbars included at well under branded-rack money
Good to know. Adjustability means more joints, and more joints means more things to re-torque after the first few loaded trips. The listing states no load rating and no material, so treat both as unknown.
1000 lb published capacity with both drilling and non-drilling install options in the box. If what you actually need is a number on paper for heavier loads, this is the cheapest way to get it.
Build
9.0
Capacity
9.5
Install
9.4
Versatility
9.2
Value
9.7
Why we picked it
+1000 lb published
+Both mounting methods included
+Very low price for the rating
Good to know. A high rating on a budget rack is a rating for the tube, not the whole installation. Check your clamp or bolt points against the load before trusting it.
$279.007% off · Price as of November 20, 2026. #ad
Adjustable 58-69 in, rated to 1000 lb, and tall enough to carry over the cab line. The height is what makes it usable for lumber as well as ladders — a low rack forces long material to sit on the tailgate.
Build
9.2
Capacity
9.5
Install
9.2
Versatility
9.6
Value
9.5
Why we picked it
+Tall enough to clear the cab for long material
+1000 lb published capacity
+Adjustable width covers most full-size beds
Good to know. Height costs you in wind noise and in low clearances. If the truck lives in a parking garage, measure the entrance first.
$699.9520% off · Price as of November 20, 2026. #ad
TracRac's entry rack, built on the clamp system the trade standardized on. The reason to pay for it is that the crossbars stay square to each other after a year of loading — budget racks walk out of alignment and then you are fighting the straps.
Build
9.6
Capacity
9.4
Install
9.5
Versatility
9.4
Value
8.9
Why we picked it
+Crossbars stay square under repeated loading
+No-drill clamp system comes off cleanly when the truck is sold
+Thule accessory ecosystem fits it
Good to know. It is a lot of money for a two-bar rack. If the rack carries a ladder twice a month, a clamp-on steel rack does the job for a quarter of the price.
Published figures only. A rack whose maker states no capacity or no range is listed as not published, never estimated.
Published capacity
Width or height range
Mounting
AA-Racks X31
800 lb
Extendable, range not published
Clamp-on
JY PERFORMANCE DAC875
800 lb tested
49-73 in rail span
4 no-drill J-bolt clamps
MONOKING bed rack
Not published
17-25 in bar height
Bed-rail mount, named Ram fitment
VEVOR 1000 lb
1000 lb / 454 kg
Not published
Drilling or non-drilling
ECOTRIC 1000 lb
1000 lb
58-69 in width
Clamp-on
Thule TracRac TracONE
Not published
Not published
Clamp-on, no drilling
Those capacity figures all deserve the same caveat, and none of the listings gives it. A published rating describes the rack, tested on its own. What carries the load on your truck is the rack plus its clamps plus the bed rail underneath, and the weakest of those three sets the real limit. What a ladder rack will actually hold works through where the number comes from and where it stops applying.
Measuring a Ram rail, in four minutes
Exterior bed rail width. Outside edge to outside edge, across the top of the rails, at the point nearest the cab. Keep the tape taut over five and a half feet or you will read an inch wide. Expect about 66 in.
Rail lip condition. A J-bolt or a clamp grips the underside of the rail lip. Look along it for a previous box's bite marks, a bonded rail cap, a utility track or a RamBox lid, all of which change what the clamp lands on.
Rear glass clearance. Hold a tape at the rack's front bar position and look at where the glass is. This is the measurement people skip and then regret, and it is worst on a lowered truck or one with a sliding rear window.
Load height above the cab. An over-cab rack solves the lumber problem and creates a clearance problem. Measure your garage, your yard gate and the drive-through you use before you buy a tall rack.
Ram's own published cargo box figures — 67.4 in of floor on the 5'7" bed and 76.3 in on the 6'4" bed, 51.0 in between the wheelhouses, and 21.4 and 21.5 in of box depth respectively — are reproduced with their sources on the Ram 1500 bed dimensions page. None of them changes which rack fits; they decide what you can stack under it, which is the next question after the rack is on.
A rack, a cover and a box on the same Ram
Ram short beds get covered more often than not, and most clamp-on racks are quietly hostile to a cover because they want the same rail top the cover's own rails occupy.
The JY PERFORMANCE rack publishes the exclusion outright: its listing rules out trucks running a tool box, a utility track or a tonneau cover. That is the maker's own statement rather than our caution, and it applies to a great many clamp-on racks that do not say so as plainly. If you are fitting both, decide the cover first — the best tonneau covers for a Ram 1500 ranks the covers that fit this truck, and running a rack with a cover sets out the clearances that make the combination work.
The MONOKING rack is the one here with a direct answer to the problem. Its bars set anywhere from 17 to 25 inches above the mount, so on a bed already carrying a crossover box the bars can be raised to clear the lid instead of fighting it. The listing publishes no load rating and no material, which is a real mark against it and is why it sits third rather than first, but on a bed with something already in it the adjustable height is worth more than a number on a box.
What a ladder rack is not
A ladder rack spans the bed and carries long material above it. A headache rack stands at the bulkhead and protects the rear glass from a load that shifts forward. They get bought with the same search and they do different jobs — plenty of working trucks want both, and neither substitutes for the other. Headache rack against ladder rack is the full comparison. And if the rack has taken both rails, lockable storage has to go somewhere that needs no rail: the best small underbody tool boxes are the boxes that hang off the frame instead.
What we would actually buy
On a Ram 1500 with an uncovered bed, carrying ladders and conduit: the AA-Racks X31. The 800 lb published figure is more than any ladder on a half-ton needs, the extendable width covers a 66 in rail, and the money saved against the premium racks buys the straps and the bed mat too. It is the budget pick on this page and it is also the one we would fit.
On a leased truck, or one going back to a dealer: the JY PERFORMANCE DAC875, for the four J-bolts and the published 49 to 73 inch span. Nothing gets drilled, nothing needs sealing, and the rack comes off in an afternoon. Read its own exclusion list first — if the truck has a tool box or a cover, this is not the rack.
On a bed that already has a box or a cover on it: the MONOKING, accepting that the capacity is unpublished and sizing the load accordingly. It names the Ram 1500 in its fitment list, which none of the other five racks here does, and the 17 to 25 inch height range is the feature that lets a rack and a box share a bed without either being removed.
If the rack will be loaded hard and often and has to stay square: the Thule TracRac TracONE. It publishes no capacity figure, which is a genuine mark against it on this page, and what you are paying for instead is a clamp system that keeps the two bars parallel after a year of loading. Budget racks that walk out of alignment make every strap job harder, and that is the failure the trade pays to avoid.
Questions people actually ask
What size ladder rack fits a Ram 1500?
The Ram 1500's exterior bed rail width is about 66 inches, the widest of the four trucks on this site, so you want a rack whose published range brackets that figure with travel left over — the JY PERFORMANCE rack's 49-73 in span is the clearest example here. Measure outside to outside across the top of your own rails nearest the cab before ordering, because a bonded rail cap, a drop-in liner lip or a RamBox lid changes what the clamp lands on.
Will a universal ladder rack fit a Ram 1500?
Usually, if the width range covers about 66 inches and the bed rails are sound and accessible. The catch on this truck is margin rather than fit: the ECOTRIC rack's published 58-69 in range leaves only about three inches of travel at a Ram rail, which a rail cap or a liner lip can use up. Racks that publish no range at all — the AA-Racks, VEVOR and Thule parts here — are sold for full-size beds and work on this truck, but you will not know how much adjustment is left until it is on.
Can I fit a ladder rack to a Ram with RamBox?
Ask the rack maker about your specific part before you order. RamBox puts lockable storage into the bed side walls and its lids interrupt the rail profile a clamp-on rack needs to grip. None of the racks on this page publishes a RamBox position either way, and where a maker has not published an answer we will not invent one. The same caution applies to crossover tool boxes on a RamBox bed.
How much weight can a Ram 1500 ladder rack hold?
Three of the six racks on this page publish a figure: 800 lb, 800 lb tested and 1000 lb. The other three publish none and their cards say so. Treat any published rating as describing the rack alone — the real limit is the lowest of the rack, its clamps and the bed rail they grip, and a ladder's own duty rating under OSHA 29 CFR 1926.1053 is a separate limit again.
Do I have to drill into the bed rails?
No. Five of the six racks here mount without drilling — clamps on the AA-Racks, ECOTRIC and Thule racks, four J-bolts on the JY PERFORMANCE rack, and both options in the box on the VEVOR. A no-drill mount keeps the rails intact for resale and is usually the only option on a leased truck. Drilled mounts are stiffer and permanent, and the holes need sealing properly or they rust from the inside out.
Can I run a ladder rack and a tonneau cover on a Ram 1500?
Only with parts chosen for it. The JY PERFORMANCE listing explicitly excludes trucks with a tonneau cover, a tool box or a utility track, and many clamp-on racks have the same conflict without stating it, because the clamp wants the rail top the cover's rails occupy. The MONOKING rack's 17-25 in adjustable bar height is the workaround on this page: set the bars above the obstruction rather than trying to share the rail with it.
Last reviewed November 20, 2026. Think a figure here is wrong? Tell us at contact@toolboxandtruck.com and we will check it, fix it and date the correction — see our editorial policy.